If you have a new Sun Joe pressure washer that is leaking from the bottom, you might as well send it back and get a replacement. However, if you have been using it for a while and you notice this problem, it could be due to a bunch of reasons.
In this article, we will look at the reasons why the Sun Joe pressure washer is leaking from the bottom and the right fixes to apply.
Sun Joe Pressure Washer Leaking from Bottom: How to Fix
1. Identify the Source of the Leak
The first step in fixing a leaking Sun Joe pressure washer is to determine where the leak is coming from. Look for wet spots or drips on the bottom of the unit, as well as any visible cracks or damage. This will help you identify the specific area that needs to be repaired.
2. Check the Hose Connections
One common cause of leaks in pressure washers is a loose or damaged hose connection. To check the hose connections, follow these steps:
- Turn off the pressure washer and disconnect it from the power source.
- Inspect all of the hoses, looking for any visible signs of damage or looseness.
- Tighten any loose connections, using a wrench if necessary.
- If you find any damaged hoses, consider replacing them.
3. Inspect the Pump
If you’re still experiencing leakage issues, it could be due to a damaged pump. To check the pump,:
- Ensure that the washer is turned off and disconnected from the power source.
- Locate the pump, which is usually located near the bottom of the unit.
- Inspect the pump for any visible cracks or damage.
- If you find any damage, consider replacing the pump.
4. Replace Damaged Seals or Gaskets
If the leak is coming from a seal or gasket, you will have to get it replaced. To do this, you will need to access the area where the seal or gasket is located. To do this:
- Make sure the pressure washer is turned off and disconnect it from the power source.
- Refer to the manufacturer’s manual to find the location of the seal or gasket.
- Depending on the specific model of your pressure washer, you may need to remove a panel or disassemble the unit to access the seal or gasket.
- Once you have access to the seal or gasket, remove it and replace it with a new one.
5. Checking the Unloader Valve
The unloader valve is a crucial part of the pressure washer. Its function is to regulate the flow of water through the pressure washer. When damaged, it would lead to leaks in the pressure washer. To check the unloader valve for leaks, follow these steps:
- Start by turning off the pressure washer and disconnect it from the power source.
- Locate the unloader valve, which is usually located near the pump.
- Inspect the unloader valve for any visible signs of damage or wear.
- If you find any damage, consider replacing the unloader valve.
6. Checking the Water Inlet Filter
The water inlet filter in the pressure washer protects the pump from contaminants by filtering out debris and dirt in the water before it enters the pressure washer. A clogged or damaged filter could lead to leaks. To check the water inlet filter, follow these steps:
- With the pressure washer turned off, locate the water inlet filter, which is usually located near the inlet hose.
- Inspect the filter for any visible signs of clogging or damage.
- If the filter is clogged, clean it or replace it as needed.
7. Checking the Water Outlet Hose
In some cases, the leak could be coming from the water outlet hose. This could be due to a loose or damaged connection. You can check the water outlet hose using the steps below:
- Checking the water outlet hose involves a visual inspection. Ensure that the pressure washer is turned off before you start.
- When done, inspect the water outlet hose for any visible signs of looseness or damage.
- Tighten any loose connections and replace any damaged hoses.
8. Checking the Nozzle
The nozzle of the pressure washer directs the water flow from the pressure washer. If the nozzle is damaged or not properly seated, it could cause the pressure washer to leak. To check the nozzle, follow the steps below:
- Turn off the pressure washer and locate the nozzle and inspect it for any visible signs of damage.
- If the nozzle is damaged, consider replacing it.
- Make sure the nozzle is properly seated and tightened to prevent leaks.
9. Contacting Sun Joe Customer Service
If you’re unable to identify the source of the leak or you’re unable to fix it, it might be best to consider contacting Sun Joe customer service for further assistance. If the pressure washer is still under warranty, you might get it fixed for free or get a replacement. If not, then you could get information and guidance on how to repair your specific model of pressure washer.
Preventing Future Leaks
To help prevent future leaks in your Sun Joe pressure washer, there are a few steps you can take:
- Store the unit properly. Make sure to store your pressure washer in a dry, covered area to protect it from the elements.
- Use the correct nozzle. One of the easiest ways to prevent leaks is to use the right nozzle for the job. This will also help prevent damage to the unit.
- Follow the manufacturer’s maintenance schedule. Regular maintenance, as outlined in the manufacturer’s manual, can help prevent issues such as leaks and extend the lifespan of your pressure washer. Ensure you follow through at the right intervals.
- Use the unit correctly. Avoid using the pressure washer for tasks it is not designed for, and follow the manufacturer’s instructions for proper usage.
By following these steps, you can help prevent leaks in your Sun Joe pressure washer and keep it running smoothly for years to come.