Products recommended in the post contain affiliate links. If you purchase something through our posts, we may receive a commission at no extra charge to you. See our full disclosures here.

Bissell Vacuum Not Spinning? Here’s How to Fix

A Bissell vacuum that is not spinning tends to happen to both new and older models of the vacuum. If you’re facing this problem, there is no need for worries. 

Troubleshooting a Bissell vacuum that is not spinning can be a relatively simple process, but it can also require some more in-depth repair work. 

Here is a guide to help you fix your Bissell vacuum that is not spinning:

Bissell Vacuum Not Spinning? Here’s How to Fix

bissell vacuum not spinning

1. Check the Power Source

Make sure the vacuum is properly plugged in and that the outlet is working. If the outlet is not working, try plugging the vacuum into a different outlet.

  • You should also check the fuse or circuit breaker and replace if necessary.
  • Finally, you want to check the power cord for any damage, fraying or breaks. If the cord is damaged, you will have to get it replaced.

2. Check the Filter

A clogged filter can restrict airflow, causing the vacuum to lose suction and not spin. You will have to remove and clean the filter to see if it will get the vacuum

  • Make sure the filter is properly installed. An improperly installed filter can also cause the vacuum to lose suction.
  • While cleaning the filter, you should also check for any rips or tears and replace if necessary.
  • Check if the filter is washable or not before cleaning it. If it’s not, it should be replaced.

3. Check the Brush Roller

  • Remove the brush roller and inspect it for debris or tangles. Clear any debris or tangles from the brush roller.
  • Check the belt and make sure it is not broken or worn. If the belt is broken or worn, have it replaced.
  • Check the brush roll for any damage or wear. If you notice any damages, get it replaced.
  • Make sure the brush roll is properly installed and that there are no obstructions blocking it from spinning.

4. Check the Hose

  • Inspect the hose for any kinks or clogs. Clear any clogs or kinks from the hose.
  • Make sure the hose is properly attached to the vacuum and that there are no leaks.
  • Check if the hose is damaged or worn, if it is, then you will have to replace it.

5. Check the Motor

If the vacuum is still not spinning after checking the above items, the problem may be with the motor.

Consult the vacuum’s manual or contact Bissell customer service for instructions on how to check and repair the motor.

  • Check the motor for any visible damage or wear.
  • Check the motor fan for any debris or obstruction, clean if necessary.

If none of these solutions work, it may be best to contact Bissell customer service or take the vacuum to a professional repair shop. Keep in mind that some vacuum models have different design and troubleshooting steps, so make sure to check your vacuum manual or consult with the manufacturer’s customer service if you are uncertain.

How to Clean the Clogged Filter

Cleaning a clogged filter is an important step in maintaining your Bissell vacuum’s performance. Here is a guide on how to clean your clogged filter:

  • Access the filter: In most models, the filter is located in the dirt container or the base of the vacuum. Refer to the vacuum’s manual for the specific location of the filter in your model.
  • Remove the filter: Carefully remove the filter from the vacuum, being mindful of any clips or latches that may be holding it in place.
  • Tap out the debris: Gently tap the filter over a trash can to remove as much debris as possible.
  • Rinse the filter: If the filter is washable, rinse it thoroughly under running water. Make sure to remove all the debris. Avoid using hot water, and don’t use detergent or soap.
  • Dry the filter: Allow the filter to air dry completely before reinserting it into the vacuum. Make sure it is completely dry before you reinsert it, otherwise it could damage the vacuum.
  • Reinstall the filter: Carefully reinsert the filter into the vacuum, making sure it is properly seated and securely in place.
  • Repeat the cleaning process: Depending on the usage and environment, it is recommended to clean the filter every 3-6 months.

Note: Not all filters are washable, so make sure to check your vacuum manual or consult with the manufacturer’s customer service before attempting to clean the filter. Also, some filters are permanent and are not meant to be cleaned, they should be replaced when they are clogged.

 How to Clear the Hose of Clogs and Kinks

To clear your clogged or kinked hose, follow the steps below

  • Locate the hose: You can find the hose in the base of the vacuum or attached to the wand. You can check the vacuum’s manual to get the actual location.
  • Detach the hose: Detach the hose from the vacuum and the wand.
  • Inspect the hose: Visually inspect the hose for any clogs or kinks.
  • Clear the clogs: If you find any clogs, use a long brush or a straightened coat hanger to carefully remove the clog. Be sure to remove the clog from both ends of the hose to ensure that it is completely clear.
  • Straighten kinks: If there are any kinks, straighten the hose by gently flexing it back and forth. Be careful not to damage the hose while straightening it.
  • Reattach the hose: When done, reattach the hose to the vacuum and the wand, making sure it is properly seated and securely in place.
  • Turn on the vacuum and test the hose: Turn on the vacuum and test the hose for any suction loss or clogs.
  • Repeat the process: If the hose is still clogged or kinked, repeat the process until the hose is completely clear.

It’s important to note that some hoses are not detachable and should be checked with the vacuum on while it’s running, if the suction is low and the hose is clogged or kinked, try to straighten the hose by gently flexing it back and forth without detaching it.